DC5800 PCI SIMPLE COMMUNICATIONS CONTROLLER DRIVERS FOR WINDOWS

You can use two different methods to remove the ReadyBoost card. You can not save to the hard drive. Remove any diskette, compact disc, or media card from the computer. The computer will beep once after a POST text message is displayed on the screen. Adherence to the procedures and precautions described in this chapter is essential for proper service.

Uploader: Malajas
Date Added: 9 October 2004
File Size: 45.76 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 95702
Price: Free* [*Free Regsitration Required]

Chassis Designations Identifying the Chassis, Routine Care, and Disassembly Preparation This chapter provides general service information for the computer. A pin connector, as well as a separate post, secures the ReadyBoost card to the system board. Be careful not to pinch any cables or wires when rotating the drive cage down. Remove the four screws from the bottom of the hard drive carrier.

Country-specific Requirements Country-Specific Requirements Additional requirements specific to a country are shown in parentheses and explained below. Removing and Replacing dc5800 pci simple communications controller Removable 3. Connect the power and data cables to the drive as indicated in the following illustrations.

The security screw is located on the fan duct inside the chassis. Page 92 Page 93 Page 94 – Removing an Internal 3. Cause Solution Program in use has stopped responding to commands. Insert the new battery and position the dc5800 pci simple communications controller back in place. Cable Routing Cable Routing When servicing the computer, please note the original locations of the cables and how they are routed in the chassis.

Decoder software is not communucations. To learn more about the Proactive Change Notification program and create a custom profile, visit http: Rotate the drive cage to its upright position. Slide the hard drive back to disconnect d5800 from the carrier then lift it up and out of the carrier.

To install the power supply, reverse the removal procedure. Cause Dc5800 pci simple communications controller Modem is not set up properly. When reconnecting the cables it is important that they be positioned so they do not interfere with the rotation of the drive cage or power supply.

You may need to reconfigure the computer when you add or remove hardware, such dc5800 pci simple communications controller an additional diskette drive. Page 90 Page 91 – Installing an External 5. Solving Drive Key Problems If you encounter Drive Key problems, common causes and solutions are listed in the following table. Before removing the computer access panel, ensure that the computer is turned off and that the power cord is disconnected from the electrical outlet.

Never remove a wide leveled key like the space bar from the keyboard. Network controller is not set up properly. Fill out the form, click the Begin button, and follow the dc5800 pci simple communications controller on the screen. With the power cord disconnected, press the power button again to drain the system of any residual power. Page 96 Connect the power cable 1 and data cable 2 to the back of the hard drive. Reconnect keyboard with computer turned off.

Compaq dc5800 – Microtower PC Reference Manual

Power Cord Communucations Requirements The power supplies on some computers have external power switches. Mouse may need repair. If this fails, press the power button for four or more seconds to turn off the power.

To install a new expansion card, hold the card just above comunications expansion socket on the system board then move dc5800 pci simple communications controller card toward the rear dc5800 pci simple communications controller the chassis 1 so that the bracket on the card is aligned with the open slot on the rear of the chassis.

Shut down the operating system properly, then turn off the computer and any external devices, and disconnect the power cord from the power outlet.

Solving Hardware Installation Controller You may need to reconfigure the computer when you add or remove hardware, such as an additional drive or expansion card. To install the access panel, reverse the removal procedure.

Refer to the number listed in the warranty or in the Support Telephone Numbers guide for technical pvi. Removing An External 5. Cable Connections Cable Connections Dc5800 pci simple communications controller board connectors are color-coded to make it easier to find the proper connection.

If you are installing a primary hard drive, use the power connector labeled P4. Carefully lift the processor from the socket 3. Beeps stop after fifth iteration but LEDs continue flashing. External Security Devices Page If you are removing a standard PCI card, hold the card at each end, and carefully rock dc5800 pci simple communications controller back and forth until the connectors pull free from the socket.

The number of heads may not exceed The information contained herein is subject to change without notice. Page Screw the lock to the chassis using the screw provided. Removing An External 3. Slide the access panel back 2 about 1.

COMPAQ DC – MICROTOWER PC REFERENCE MANUAL Pdf Download.

Type 3 Battery Holder Plug in the computer and turn on power to the computer. Loosen the four silver T15 captive screws that secure the heatsink to the system board.

Unplug the speaker cable.